FACTOID # 1: Idaho produces more milk than Iowa, Indiana and Illinois combined.
 
 Home   Encyclopedia   Statistics   States A-Z   Flags   Maps   FAQ   About 
   
 
WHAT'S NEW
 

SEARCH ALL

FACTS & STATISTICS    Advanced view

Search encyclopedia, statistics and forums:

 

 

(* = Graphable)

 

 


Encyclopedia > CPU cache
Diagram of a CPU memory cache
Diagram of a CPU memory cache

A CPU cache is a cache used by the central processing unit of a computer to reduce the average time to access memory. The cache is a smaller, faster memory which stores copies of the data from the most frequently used main memory locations. As long as most memory accesses are to cached memory locations, the average latency of memory accesses will be closer to the cache latency than to the latency of main memory. Image File history File links This is a lossless scalable vector image. ... Look up cache in Wiktionary, the free dictionary. ... Die of an Intel 80486DX2 microprocessor (actual size: 12×6. ... A BlueGene supercomputer cabinet. ... This article or section does not adequately cite its references or sources. ... Primary storage is a category of computer storage, often called main memory. ... RAM Latency is the amount of wait time that a computer experiences when trying to access data in its RAM. RAM latency is measured in front side bus clock cycles. ...


The diagram to the right shows two memories. Each location in each memory has a datum (a cache line), which in different designs ranges in size from 8 to 512 bytes. The size of the cache line is usually larger than the size of the usual access requested by a CPU instruction, which ranges from 1 to 16 bytes. Each location in each memory also has an index, which is a unique number used to refer to that location. The index for a location in main memory is called an address. Each location in the cache has a tag, which contains the index of the datum in main memory which has been cached. In a CPU's data cache, these entries are called cache lines or cache blocks. In computer science a byte is a unit of measurement of information storage, now usually considered to contain eight bits. ... In computer science, a memory address is a unique identifier for a memory location at which a CPU or other device can store a piece of data for later retrieval. ...


When the processor wishes to read or write a location in main memory, it first checks whether that memory location is in the cache. This is accomplished by comparing the address of the memory location to all tags in the cache that might contain that address. If the processor finds that the memory location is in the cache, we say that a cache hit has occurred, otherwise we speak of a cache miss. In the case of a cache hit, the processor immediately reads or writes the data in the cache line. The proportion of accesses that result in a cache hit is known as the hit rate, and is a measure of the effectiveness of the cache.


In the case of a cache miss, most caches allocate a new entry, which comprises the tag just missed and a copy of the data from memory. The reference can then be applied to the new entry just as in the case of a hit. Misses are comparatively slow because they require the data to be transferred from main memory. This transfer incurs a delay since main memory is much slower than cache memory, and also incurs the overhead for recording the new data in the cache before it is delivered to the processor.

Contents

Some details of operation

In order to make room for the new entry on a cache miss, the cache generally has to evict one of the existing entries. The heuristic that it uses to choose the entry to evict is called the replacement policy. The fundamental problem with any replacement policy is that it must predict which existing cache entry is least likely to be used in the future. Predicting the future is difficult, especially for hardware caches which use simple rules amenable to implementation in circuitry, so there are a variety of replacement policies to choose from and no perfect way to decide among them. One popular replacement policy, LRU, replaces the least recently used entry. In computer science, besides the common use as rule of thumb (see heuristic), the term heuristic has two well-defined technical meanings. ... Cache algorithms are optimizing instructions â€“ algorithms â€“ that a computer program can follow to manage a cache of information stored on the computer. ...


When data is written to the cache, it must at some point be written to main memory as well. The timing of this write is controlled by what is known as the write policy. In a write-through cache, every write to the cache causes a write to main memory. Alternatively, in a write-back cache, writes are not immediately mirrored to memory. Instead, the cache tracks which locations have been written over (these locations are marked dirty). The data in these locations is written back to main memory when that data is evicted from the cache. For this reason, a miss in a write-back cache will often require two memory accesses to service: one to read the new location from memory and the other to write the dirty location to memory.


There are intermediate policies as well. The cache may be write-through, but the writes may be held in a store data queue temporarily, usually so that multiple stores can be processed together (which can reduce bus turnarounds and so improve bus utilization). In computer architecture, a bus is a subsystem that transfers data or power between computer components inside a computer or between computers and typically is controlled by device driver software. ...


The data in main memory being cached may be changed by other entities, in which case the copy in the cache may become out-of-date or stale. Alternatively, when the CPU updates the data in the cache, copies of data in other caches will become stale. Communication protocols between the cache managers which keep the data consistent are known as coherency protocols or coherence protocols. In computer science, a coherence protocol is a protocol in systems with distributed memory (distributed shared memory systems, including multiprocessors), which maintains memory coherence according to specified consistency model. ...


The time taken to fetch a datum from memory (read latency) matters because a CPU will often run out of things to do while waiting for the datum. When a CPU reaches this state, it is called a stall. As CPUs become faster, stalls due to cache misses displace more potential computation; modern CPUs can execute hundreds of instructions in the time taken to fetch a single datum from memory. Various techniques have been employed to keep the CPU busy during this time. Out-of-order CPUs (Pentium Pro and later Intel designs, for example) attempt to execute independent instructions after the instruction which is waiting for the cache miss data. The Pentium 4 uses Simultaneous multithreading (Hyper-threading in Intel's terminology) to allow a second program to use the CPU while a first program waits for data to come from main memory. In computer engineering, out-of-order execution, OoOE, is a paradigm used in most high-performance microprocessors in order to make use of cycles that would otherwise be wasted by a certain type of costly delay. ... Pentium Pro 256 KB Pentium Pro 512 KB Pentium Pro 1 MB Pentium Pro underside (256/512) Pentium II Overdrive The Pentium Pro is a sixth-generation x86 architecture microprocessor (P6 core) by Intel originally intended to replace the original Pentium in a full range of applications, but later reduced... New Intel Pentium 4 with Hyper Threading logo The Pentium 4 is a seventh-generation x86 architecture microprocessor produced by Intel and was the companys first all-new CPU design since the Pentium Pro of 1995. ... Simultaneous multithreading, often abbreviated as SMT, is a technique for improving the overall efficiency of the hardware that executes instructions in a computer. ... Hyper-Threading (HTT = Hyper Threading Technology) is Intels trademark for their implementation of the simultaneous multithreading technology on the Pentium 4 microarchitecture. ... Intel Corporation (NASDAQ: INTC, SEHK: 4335), founded in 1968 as Integrated Electronics Corporation, is an American multinational corporation that is best known for designing and manufacturing microprocessors and specialized integrated circuits. ...


Associativity

Which memory locations can be cached by which cache locations

Recall that the replacement policy decides where in the cache a copy of a particular entry of main memory will go. If the replacement policy is free to choose any entry in the cache to hold the copy, the cache is called fully associative. At the other extreme, if each entry in main memory can go in just one place in the cache, the cache is direct mapped. Many caches implement a compromise, and are described as set associative. For example, the level-1 data cache in an AMD Athlon is 2-way set associative, which means that any particular location in main memory can be cached in either of 2 locations in the level-1 data cache. Image File history File links Compares fill possibilities for direct mapped and 2-way set associative caches. ... Image File history File links Compares fill possibilities for direct mapped and 2-way set associative caches. ... Advanced Micro Devices, Inc. ... Athlon is the brand name applied to a series of different x86 processors designed and manufactured by AMD. The original Athlon, or Athlon Classic, was the first seventh-generation x86 processor and, in a first, retained the initial performance lead it had over Intels competing processors for a significant...


Associativity is a tradeoff. If there are ten places the replacement policy can put a new cache entry, then when the cache is checked for a hit, all ten places must be searched. Checking more places takes more power, area, and potentially time. On the other hand, caches with more associativity suffer fewer misses (see conflict misses, below), so that the CPU spends less time servicing those misses. The rule of thumb is that doubling the associativity, from direct mapped to 2-way, or from 2-way to 4-way, has about the same effect on hit rate as doubling the cache size. Associativity increases beyond 4-way have much less effect on the hit rate, and are generally done for other reasons (see virtual aliasing, below).


If each location in main memory can be cached in either of two locations in the cache, one logical question is: which two? The simplest and most commonly used scheme, shown in the right-hand diagram above, is to use the least significant bits of the memory location's index as the index for the cache memory, and to have two entries for each index. One good property of this scheme is that the tags stored in the cache do not have to include that part of the main memory address which is specified by the cache memory's index. Since the cache tags are fewer bits, they take less area and can be read and compared faster.


One of the advantages of a direct mapped cache is that it allows simple and fast speculation. Once the address has been computed, the one cache index which might have a copy of that datum is known. That cache entry can be read, and the processor can continue to work with that data before it finishes checking that the tag actually matches the requested address. In computer science, speculative execution is the execution of code whose result may not actually be needed. ...


The idea of having the processor use the cached data before the tag match completes can be applied to associative caches as well. A subset of the tag, called a hint, can be used to pick just one of the possible cache entries mapping to the requested address. This datum can then be used in parallel with checking the full tag. The hint technique works best when used in the context of address translation, as explained below.


Other schemes have been suggested, such as the skewed cache, where the index for way 0 is direct, as above, but the index for way 1 is formed with a hash function. A good hash function has the property that addresses which conflict with the direct mapping tend not to conflict when mapped with the hash function, and so it is less likely that a program will suffer from an unexpectedly large number of conflict misses due to a pathological access pattern. The downside is extra latency from computing the hash function. Additionally, when it comes time to load a new line and evict an old line, it may be difficult to determine which existing line was least recently used, because the new line conflicts with data at different indexes in each way; LRU tracking for non-skewed caches is usually done on a per-set basis. A hash function [1] is a reproducible method of turning some kind of data into a (relatively) small number that may serve as a digital fingerprint of the data. ...


Cache misses

A cache miss refers to a failed attempt to read or write a piece of data in the cache, which results in a main memory access with much longer latency. There are three kinds of cache misses: instruction read miss, data read miss, and data write miss.


A cache read miss from an instruction cache generally causes the most delay, because the processor, or at least the thread of execution, has to wait (stall) until the instruction is fetched from main memory. Simultaneous multithreading, often abbreviated as SMT, is a technique for improving the overall efficiency of the hardware that executes instructions in a computer. ...


A cache read miss from a data cache usually causes less delay, because instructions not dependent on the cache read can be issued and continue execution until the data is returned from main memory, and the dependent instructions can resume execution.


A cache write miss to a data cache generally cause the least delay, because the write can be queued and there are few limitations on the execution of subsequent instructions. The processor can continue until the queue is full.


In order to lower cache miss rate, a great deal of analysis has been done on cache behavior in an attempt to find the best combination of size, associativity, block size, and so on. Sequences of memory references performed by benchmark programs are saved as address traces. Subsequent analyses simulate many different possible cache designs on these long address traces. Making sense of how the many variables affect the cache hit rate can be quite confusing. One significant contribution to this analysis was made by Mark Hill, who separated misses into three categories (known as the Three Cs):

  • Compulsory misses are those misses caused by the first reference to a datum. Cache size and associativity make no difference to the number of compulsory misses. Prefetching can help here, as can larger cache block sizes (which are a form of prefetching).
  • Capacity misses are those misses that occur regardless of associativity or block size, solely due to the finite size of the cache. The curve of capacity miss rate versus cache size gives some measure of the temporal locality of a particular reference stream. Note that there is no useful notion of a cache being "full" or "empty" or "near capacity": CPU caches almost always have nearly every line filled with a copy of some line in main memory, and nearly every allocation of a new line requires the eviction of an old line.
  • Conflict misses are those misses that could have been avoided, had the cache not evicted an entry earlier. Conflict misses can be further broken down into mapping misses, that are unavoidable given a particular amount of associativity, and replacement misses, which are due to the particular victim choice of the replacement policy.
Miss rate versus cache size on the Integer portion of SPEC CPU2000
Miss rate versus cache size on the Integer portion of SPEC CPU2000

The graph to the right summarizes the cache performance seen on the Integer portion of the SPEC CPU2000 benchmarks, as collected by Hill and Cantin [2]. These benchmarks are intended to represent the kind of workload that an engineering workstation computer might see on any given day. We can see the different effects of the three Cs in this graph. Image File history File links No higher resolution available. ... Image File history File links No higher resolution available. ...


At the far right, with cache size labelled "Inf", we have the compulsory misses. If we wish to improve a machine's performance on SpecInt2000, increasing the cache size beyond 1 MiB is essentially futile. That's the insight given by the compulsory misses.


The fully-associative cache miss rate here is almost representative of the capacity miss rate. The difference is that the data presented is from simulations assuming an LRU replacement policy. Showing the capacity miss rate would require a perfect replacement policy, i.e. an oracle that looks into the future to find a cache entry which is actually not going to be hit.


Note that our approximation of the capacity miss rate falls steeply between 32 KiB and 64 KiB. This indicates that the benchmark has a working set of roughly 64 KiB. A CPU cache designer examining this benchmark will have a strong incentive to set the cache size to 64 KiB rather than 32 KiB. Note that, on this benchmark, no amount of associativity can make a 32 KiB cache perform as well as a 64 KiB 4-way, or even a direct-mapped 128 KiB cache. A kibibyte (a contraction of kilo binary byte) is a unit of information or computer storage, commonly abbreviated KiB (never kiB). 1 kibibyte = 210 bytes = 1,024 bytes The kibibyte is closely related to the kilobyte, which can be used either as a synonym for kibibyte or to refer to...


Finally, note that between 64 KiB and 1 MiB there is a large difference between direct-mapped and fully-associative caches. This difference is the conflict miss rate. As of 2004, on-chip secondary caches tend to be in this range, because smaller caches are fast enough to be primary caches, and larger caches become too large to produce economically on-chip (Itanium 2 has a 9 MiB level-3 on-chip cache, the largest shipping on-chip cache in 2004). The insight from looking at conflict miss rates is that secondary caches benefit a great deal from high associativity. Itanium 2 logo The Itanium 2 is an IA-64 64-bit microprocessor developed jointly by Hewlett-Packard (HP) and Intel, and introduced on July 8, 2002. ...


This benefit was well known in the late 80s and early 90s, when CPU designers could not fit large caches on-chip, and could not get sufficient bandwidth to either the cache data memory or cache tag memory to implement high associativity in off-chip caches. Desperate hacks were attempted: the MIPS R8000 used expensive off-chip dedicated tag SRAMs, which had embedded tag comparators and large drivers on the match lines, in order to implement a 4 MiB 4-way associative cache. The MIPS R10000 used ordinary SRAM chips for the tags. Tag access for both ways took two cycles. To reduce latency, the R10000 would guess which way of the cache would hit on each access. A MIPS R4400 microprocessor made by Toshiba. ... Static random access memory (SRAM) is a type of semiconductor memory. ...


Address translation

Most general purpose CPUs implement some form of virtual memory. To summarize, each program running on the machine sees its own simplified address space, which contains code and data for that program only. Each program places things in its address space without regard for what other programs are doing in their address spaces. Virtual memory is an addressing scheme implemented in hardware and software that allows non-contiguous memory to be addressed as if it is contiguous. ...


Virtual memory requires the processor to translate virtual addresses generated by the program into physical addresses in main memory. The portion of the processor that does this translation is known as the memory management unit (MMU). The fast path through the MMU can perform those translations stored in the Translation Lookaside Buffer (TLB), which is a cache of mappings from the operating system's page table. A Translation Lookaside Buffer (TLB) is a cache in a CPU that is used to improve the speed of virtual address translation. ... Relationship between pages addressed by virtual addresses and the frames in physical memory, within a simple address space scheme. ...


For the purposes of the present discussion, there are three important features of address translation:

  • Latency: The physical address is available from the MMU some time, perhaps a few cycles, after the virtual address is available from the address generator.
  • Aliasing: Multiple virtual addresses can map to a single physical address. Most processors guarantee that all updates to that single physical address will happen in program order. To deliver on that guarantee, the processor must ensure that only one copy of a physical address resides in the cache at any given time.
  • Granularity: The virtual address space is broken up into pages. For instance, a 4 GiB virtual address space might be cut up into 1048576 4 KiB pages, each of which can be independently mapped. There may be multiple page sizes supported, see virtual memory for elaboration.

A historical note: the first virtual memory systems were very slow, because they required an access to the page table (held in main memory) before every programmed access to main memory. With no caches, this effectively cut the speed of the machine in half. The first hardware cache used in a computer system was not actually a data or instruction cache, but rather a TLB. Virtual memory is an addressing scheme implemented in hardware and software that allows non-contiguous memory to be addressed as if it is contiguous. ...


The existence of different physical and virtual addresses raises the question of whether virtual or physical addresses are used for the cache index and tag. The motivation to use virtual addresses is speed: a virtually-indexed, virtually-tagged data cache cuts the MMU entirely out of the load-use recurrence. The latency of that recurrence (load latency) is crucial to the performance of a CPU. Most modern level-1 caches are virtually indexed, which at least allows the MMU's TLB lookup to proceed in parallel with fetching the data from the cache RAM.


But virtual indexing is not always the best choice. It introduces the problem of virtual aliases -- the cache may have multiple locations which can store the value of a single physical address. The cost of dealing with virtual aliases grows with cache size, and as a result most level-2 and larger caches are physically indexed.


Virtual tagging is uncommon. If the TLB lookup can finish before the cache RAM lookup, then the physical address is available in time for tag compare, and there is no need for virtual tagging. Large caches, then, tend to be physically tagged, and only small, very low latency caches are virtually tagged. In recent general-purpose CPUs, virtual tagging has been superseded by vhints, as described below.


Virtual indexing and virtual aliases

The usual way the processor guarantees that virtually aliased addresses act as a single storage location is to arrange that only one virtual alias can be in the cache at any given time.


Whenever a new entry is added to a virtually-indexed cache, the processor searches for any virtual aliases already resident and evicts them first. This special handling happens only during a cache miss. No special work is necessary during a cache hit, which helps keep the fast path fast.


The most straightforward way to find aliases is to arrange for them all to map to the same location in the cache. This happens, for instance, if the TLB has e.g. 4 KiB pages, and the cache is direct mapped and 4 KiB or less.


Modern level-1 caches are much larger than 4 KiB, but virtual memory pages have stayed that size. If the cache is e.g. 16 KiB and virtually indexed, for any virtual address there are four cache locations that could hold the same physical location, but aliased to different virtual addresses. If the cache misses, all four locations must be probed to see if their corresponding physical addresses match the physical address of the access that generated the miss.


These probes are the same checks that a set associative cache uses to select a particular match. So if a 16 KiB virtually indexed cache is 4-way set associative and used with 4 KiB virtual memory pages, no special work is necessary to evict virtual aliases during cache misses because the checks have already happened while checking for a cache hit.


Using the AMD Athlon as an example again, it has a 64 KiB level-1 data cache, 4 KiB pages, and 2-way set associativity. When the level-1 data cache suffers a miss, 2 of the 16 (==64 KiB/4 KiB) possible virtual aliases have already been checked, and seven more cycles through the tag check hardware are necessary to complete the check for virtual aliases.


Virtual tags and vhints

Virtual tagging is possible too. The great advantage of virtual tags is that, for associative caches, they allow the tag match to proceed before the virtual to physical translation is done. However,

  • Coherence probes and evictions present a physical address for action. The hardware must have some means of converting the physical addresses into a cache index, generally by storing physical tags as well as virtual tags. For comparison, a physically tagged cache does not need to keep virtual tags, which is simpler.
  • When a virtual to physical mapping is deleted from the TLB, cache entries with those virtual addresses will have to be flushed somehow. Alternatively, if cache entries are allowed on pages not mapped by the TLB, then those entries will have to be flushed when the access rights on those pages are changed in the page table.

It is also possible for the operating system to ensure that no virtual aliases are simultaneously resident in the cache. The operating system makes this guarantee by enforcing page coloring, which is described below. Some early RISC processors (SPARC, RS/6000) took this approach. It has not been used recently, as the hardware cost of detecting and evicting virtual aliases has fallen and the software complexity and performance penalty of perfect page coloring has risen.


It can be useful to distinguish the two functions of tags in an associative cache: they are used to determine which way of the entry set to select, and they are used to determine if the cache hit or missed. The second function must always be correct, but it is permissible for the first function to guess, and get the wrong answer occasionally.


Some processors (e.g. early SPARCs) have caches with both virtual and physical tags. The virtual tags are used for way selection, and the physical tags are used for determining hit or miss. This kind of cache enjoys the latency advantage of a virtually tagged cache, and the simple software interface of a physically tagged cache. It bears the added cost of duplicated tags, however. Also, during miss processing, the alternate ways of the cache line indexed have to be probed for virtual aliases and any matches evicted.


The extra area (and some latency) can be mitigated by keeping virtual hints with each cache entry instead of virtual tags. These hints are a subset or hash of the virtual tag, and are used for selecting the way of the cache from which to get data and a physical tag. Like a virtually tagged cache, there may be a virtual hint match but physical tag mismatch, in which case the cache entry with the matching hint must be evicted so that cache accesses after the cache fill at this address will have just one hint match. Since virtual hints have fewer bits than virtual tags distinguishing them from one another, a virtually hinted cache suffers more conflict misses than a virtually tagged cache.


Perhaps the ultimate reduction of virtual hints can be found in the Pentium 4 (Willamette and Northwood cores). In these processors the virtual hint is effectively 2 bits, and the cache is 4-way set associative. Effectively, the hardware maintains a simple permutation from virtual address to cache index, so that no CAM is necessary to select the right one of the four ways fetched.


Page coloring

Large physically indexed caches (usually secondary caches) run into a problem: the operating system rather than the application controls which pages collide with one another in the cache. Differences in page allocation from one program run to the next lead to differences in the cache collision patterns, which can lead to very large differences in program performance. These differences can make it very difficult to get a consistent and repeatable timing for a benchmark run, which then leads to frustrated sales engineers demanding that the operating system authors fix the problem.


To understand the problem, consider a CPU with a 1 MiB physically indexed direct-mapped level-2 cache and 4 KiB virtual memory pages. Sequential physical pages map to sequential locations in the cache until after 256 pages the pattern wraps around. We can label each physical page with a color of 0-255 to denote where in the cache it can go. Locations within physical pages with different colors cannot conflict in the cache.


A programmer attempting to make maximum use of the cache may arrange his program's access patterns so that only 1 MiB of data need be cached at any given time, thus avoiding capacity misses. But he should also ensure that the access patterns do not have conflict misses. One way to think about this problem is to divide up the virtual pages the program uses and assign them virtual colors in the same way as physical colors were assigned to physical pages before. The programmer can then arrange the access patterns of his code so that no two pages with the same virtual color are in use at the same time. There is a wide literature on such optimizations (e.g. loop nest optimization), largely coming from the High Performance Computing (HPC) community. Loop nest optimization (LNO) is a compiler optimization that makes possible large reductions in the cache bandwidth necessary for some pervasive algorithms. ... The field of high performance computing (HPC) comprises computing applications on (parallel) supercomputers and computer clusters. ...


The snag is that while all the pages in use at any given moment may have different virtual colors, some may have the same physical colors. In fact, if the operating system assigns physical pages to virtual pages randomly and uniformly, it is extremely likely that some pages will have the same physical color, and then locations from those pages will collide in the cache (this is the birthday paradox). In probability theory, the birthday paradox states that given a group of 23 (or more) randomly chosen people, the probability is more than 50% that at least two of them will have the same birthday. ...


The solution is to have the operating system attempt to assign different physical color pages to different virtual colors, a technique called page coloring. Although the actual mapping from virtual to physical color is irrelevant to system performance, odd mappings are difficult to keep track of and have little benefit, so most approaches to page coloring simply try to keep physical and virtual page colors the same.


If the operating system can guarantee that each physical page maps to only one virtual color, then there are no virtual aliases, and the processor can use virtually indexed caches with no need for extra virtual alias probes during miss handling. Alternatively, the O/S can flush a page from the cache whenever it changes from one virtual color to another. As mentioned above, this approach was used for some early SPARC and RS/6000 designs.


Cache hierarchy in a modern processor

Modern processors have multiple interacting caches on chip. Two issues have driven the development of the modern cache hierarchy.


Specialized caches

The first issue is that pipelined CPUs access memory from multiple points in the pipeline: instruction fetch, virtual-to-physical address translation, and data fetch. For a simple example, see Classic RISC Pipeline. The natural design is to use different physical caches for each of these points, so that no one physical resource has to be scheduled to service two points in the pipeline. Thus the pipeline naturally ends up with at least three separate caches (instruction, TLB, and data), each specialized to its particular role. The introduction to this article provides insufficient context for those unfamiliar with the subject matter. ...


Victim cache

A victim cache is a cache used to hold blocks evicted from a CPU cache due to a conflict or capacity miss. The victim cache lies between the main cache and its refill path, and only holds blocks that were evicted from that cache on a miss. This technique is used to reduce the penalty incurred by a cache on a miss.


The original victim cache on the HP PA7200 was a small, fully-associative cache. Later processors, such as the AMD K7 and K8, used the very large secondary cache as a victim cache, to avoid duplicate storage of the contents of the large primary cache.


Trace cache

One of the more extreme examples of cache specialization is the trace cache found in the Intel Pentium 4 microprocessors. A trace cache is a mechanism for increasing the instruction fetch bandwidth and decreasing power consumption (in the case of the Pentium 4) by storing traces of instructions that have already been fetched and decoded. The mechanism was first proposed by Eric Rotenberg, Steve Bennett, and Jim Smith in their 1996 paper "Trace Cache: a Low Latency Approach to High Bandwidth Instruction Fetching." In computer science, an instruction typically refers to a single operation of a processor within a computer architecture. ... Steve Bennett is the leader of Starchaser, a rocket building program for the x-prize. ...


A trace cache stores instructions either after they have been decoded, or as they are retired. Generally, instructions are added to trace caches in groups representing either individual basic blocks or dynamic instruction traces. A basic block consists of a group of non-branch instructions ending with a branch. A dynamic trace ("trace path") contains only instructions whose results are actually used, and eliminates instructions following taken branches (since they are not executed); a dynamic trace can be a concatenation of multiple of basic blocks. This allows the instruction fetch unit of a processor to fetch several basic blocks, without having to worry about branches in the execution flow.


Trace lines are stored in the trace cache based on the program counter of the first instruction in the trace and a set of branch predictions. This allows for storing different trace paths that start on the same address, each representing different branch outcomes. In the instruction fetch stage of a pipeline, the current program counter along with a set of branch predictions is checked in the trace cache for a hit. If there is a hit, a trace line is supplied to fetch which does not have to go to a regular cache or to memory for these instructions. The trace cache continues to feed the fetch unit until the trace line ends or until there is a misprediction in the pipeline. If there is a miss, a new trace starts to be built. The program counter (also called the instruction pointer in some computers) is a register in a computer processor which indicates where the computer is in its instruction sequence. ... In a computer processor, a branch misprediction occurs when the branch predictor of a processor predicts a branch to go one way, and it is later resolved to go another. ...


Trace caches are also used in processors like the Intel Pentium 4 to store already decoded micro-operations, or translations of complex x86 instructions, so that the next time an instruction is needed, it does not have to be decoded again. Intel Corporation (NASDAQ: INTC, SEHK: 4335), founded in 1968 as Integrated Electronics Corporation, is an American multinational corporation that is best known for designing and manufacturing microprocessors and specialized integrated circuits. ... New Intel Pentium 4 with Hyper Threading logo The Pentium 4 is a seventh-generation x86 architecture microprocessor produced by Intel and was the companys first all-new CPU design since the Pentium Pro of 1995. ...


See the full text of Smith, Rotenberg and Bennett's paper at Citeseer. CiteSeer is a public speciality scientific and academic search engine and digital library that was created by researchers Dr. Steve Lawrence, Kurt Bollacker and Dr. Lee Giles while they were at the NEC Research Institute (now NEC Labs), Princeton, New Jersey, USA. CiteSeer crawls and harvests academic and scientific documents...


Harvard architecture

Pipelines with separate instruction and data caches are said to have a Harvard architecture. Originally, this phrase referred to machines with separate instruction and data memories, so that there was no way for a program to alter its instructions. The term Harvard architecture originally referred to computer architectures that used physically separate storage and signal pathways for their instructions and data (in contrast to the von Neumann architecture). ...


Multi-level caches

The second issue is the fundamental tradeoff between cache latency and hit rate. Larger caches have better hit rates but longer latency. To ameliorate this tradeoff, many computers use multiple levels of cache, with small fast caches backed up by larger slower caches. As the latency difference between main memory and the fastest cache has become larger, some processors have begun to utilize as many as three levels of on-chip cache. For example, in 2003, Itanium 2 began shipping with a 6 MiB unified level 3 cache on-chip. The IBM Power 4 series has a 256 MiB level 3 cache off chip, shared among several processors. Itanium 2 logo The Itanium 2 is an IA-64 64-bit microprocessor developed jointly by Hewlett-Packard (HP) and Intel, and introduced on July 8, 2002. ...


Multi-level caches generally operate by checking the smallest Level 1 (L1) cache first; if it hits, the processor proceeds at high speed. If the smaller cache misses, the next larger cache is checked, and so on, before main memory is checked.


Multi-level caches introduce new design decisions. For instance, in some processors (like the Intel Pentium II, III, and 4, as well as most RISCs), the data in the L1 cache may also be in the L2 cache. These caches are called inclusive. Other processors (like the AMD Athlon) have exclusive caches — data is guaranteed to be in at most one of the L1 and L2 caches. Pentium II – front view The Pentium II is an x86 architecture microprocessor by Intel, introduced on May 7, 1997. ... Pentium III logo The Pentium III is an x86 (more precisely, an i686) architecture microprocessor by Intel, introduced on February 26, 1999. ... New Intel Pentium 4 with Hyper Threading logo The Pentium 4 is a seventh-generation x86 architecture microprocessor produced by Intel and was the companys first all-new CPU design since the Pentium Pro of 1995. ...


The advantage of exclusive caches is that they store more data. This advantage is larger with larger caches. When the L1 misses and the L2 hits on an access, the hitting cache line in the L2 is exchanged with a line in the L1. This exchange is quite a bit more work than just copying a line from L2 to L1, which is what an inclusive cache does.


Some implementations of inclusive caches guarantee that all data in the L1 cache is also in the L2 cache. One advantage of strictly inclusive caches is that when external devices or other processors in a multiprocessor system wish to remove a cache line from the processor, they need only have the processor check the L2 cache. In cache hierarchies which do not enforce inclusion, the L1 cache must be checked as well. As a drawback, there is a correlation between the associativities of L1 and L2 caches: if the L2 cache does not have at least as much ways as all L1 caches together, the effective associativity of the L1 caches is restricted.


Another advantage of inclusive caches is that the larger cache can use larger cache lines, which reduces the size of the secondary cache tags. If the secondary cache is an order of magnitude larger than the primary, and the cache data is an order of magnitude larger than the cache tags, this tag area saved can be comparable to the incremental area needed to store the L1 cache data in the L2.


As mentioned above, larger computers sometimes have another cache between the L2 cache and main memory called an L3 cache. This cache can be implemented on a separate chip from the CPU, and, as of 2004, may range in size from 2 to 256 megabytes. An off chip L3 cache will generally cost well in excess of $1000 to implement[citation needed], and its benefits depend on the application's access patterns. High-end x86 workstations and servers are now available with an L3 cache option implemented on the microprocessor die, increasing the speed and reducing the cost substantially. For example, Intel's Xeon MP product code-named "Tulsa" features 16 MiB of on-die L3 cache, shared between two processor cores. 2004 is a leap year starting on Thursday of the Gregorian calendar. ...


Finally, at the other end of the memory hierarchy, the CPU register file itself can be considered the smallest, fastest cache in the system, with the special characteristic that it is scheduled in software -- typically by a compiler, as it allocates registers to hold values retrieved from main memory. (See especially loop nest optimization.) Register files sometimes also have hierarchy: The Cray-1 (circa 1976) had 8 address "A" and 8 scalar data "S" registers that were generally usable. There was also a set of 64 address "B" and 64 scalar data "T" registers that took longer to access, but were faster than main memory. The "B" and "T" registers were provided because the Cray-1 did not have a data cache. (The Cray-1 did, however, have an instruction cache.) A register file is an array of processor registers in a central processing unit (CPU). ... Loop nest optimization (LNO) is a compiler optimization that makes possible large reductions in the cache bandwidth necessary for some pervasive algorithms. ... CRAY-1 at the EPFL in Switzerland. ...


Example: the K8

To illustrate both specialization and multi-level caching, here is the cache hierarchy of the AMD Athlon 64, whose core design is known as the K8 [1] AMD Logo The Athlon 64 is an eighth-generation, AMD64 architecture microprocessor produced by AMD, released on September 23, 2003[1]. It is the third processor to bear the name Athlon, and the immediate successor to the Athlon XP[2]. The second processor (after the Opteron) to implement AMD64 architecture...

Example of hierarchy, the K8
Example of hierarchy, the K8

The K8 has 4 specialized caches: an instruction cache, an instruction TLB, a data TLB, and a data cache. Each of these caches is specialized: Image File history File links This is a lossless scalable vector image. ... A Translation Lookaside Buffer (TLB) is a cache in a CPU that is used to improve the speed of virtual address translation. ...

  • The instruction cache keeps copies of 64 byte lines of memory, and fetches 16 bytes each cycle. Each byte in this cache is stored in ten bits rather than 8, with the extra bits marking the boundaries of instructions (this is an example of predecoding). The cache has only parity protection rather than ECC, because parity is smaller and any damaged data can be replaced by fresh data fetched from memory (which always has an up-to-date copy of instructions).
  • The instruction TLB keeps copies of page table entries (PTEs). Each cycle's instruction fetch has its virtual address translated through this TLB into a physical address. Each entry is either 4 or 8 bytes in memory. Each of the TLBs is split into two sections, one to keep PTEs that map 4 KiB, and one to keep PTEs that map 4 MiB or 2 MiB. The split allows the fully associative match circuitry in each section to be simpler. The operating system maps different sections of the virtual address space with different size PTEs.
  • The data TLB has two copies which keep identical entries. The two copies allow two data accesses per cycle to translate virtual addresses to physical addresses. Like the instruction TLB, this TLB is split into two kinds of entries.
  • The data cache keeps copies of 64 byte lines of memory. It is split into 8 banks (each storing 8 KiB of data), and can fetch two 8-byte data each cycle so long as those data are in different banks. There are two copies of the tags, because each 64 byte line is spread among all 8 banks. Each tag copy handles one of the two accesses per cycle.

The K8 also has multiple-level caches. There are second-level instruction and data TLBs, which store only PTEs mapping 4 KiB. Both instruction and data caches, and the various TLBs, can fill from the large unified L2 cache. This cache is exclusive to both the L1 instruction and data caches, which means that any 8-byte line can only be in one of the L1 instruction cache, the L1 data cache, or the L2 cache. It is, however, possible for a line in the data cache to have a PTE which is also in one of the TLBs—the operating system is responsible for keeping the TLBs coherent by flushing portions of them when the page tables in memory are updated. Look up Parity in Wiktionary, the free dictionary Parity is a concept of equality of status or functional equivalence. ... In information theory and coding, an error-correcting code or ECC is a code in which each data signal conforms to specific rules of construction so that departures from this construction in the received signal can generally be automatically detected and corrected. ...


The K8 also caches information that is never stored in memory—prediction information. These caches are not shown in the above diagram. As is usual for this class of CPU, the K8 has fairly complex branch prediction, with tables that help predict whether branches are taken and other tables which predict the targets of branches and jumps. Some of this information is associated with instructions, in both the level 1 instruction cache and the unified secondary cache. In computer architecture, a branch predictor is the part of a processor that determines whether a conditional branch in the instruction flow of a program is likely to be taken or not. ...


The K8 uses an interesting trick to store prediction information with instructions in the secondary cache. Lines in the secondary cache are protected from accidental data corruption (e.g. by an alpha particle strike) by either ECC or parity, depending on whether those lines were evicted from the data or instruction primary caches. Since the parity code takes fewer bits than the ECC code, lines from the instruction cache have a few spare bits. These bits are used to cache branch prediction information associated with those instructions. The net result is that the branch predictor has a larger effective history table, and so has better accuracy. An alpha particle is deflected by a magnetic field Alpha particles (named after the first letter in the Greek alphabet, α) are a highly ionizing form of particle radiation which have low penetration. ... In information theory and coding, an error-correcting code or ECC is a code in which each data signal conforms to specific rules of construction so that departures from this construction in the received signal can generally be automatically detected and corrected. ... In the usage in telecommunication, the number of 1 bits in the binary value is counted. ...


More hierarchies

Other processors have other kinds of predictors (e.g. the store-to-load bypass predictor in the DEC Alpha 21264), and various specialized predictors are likely to flourish in future processors.


These predictors are caches in the sense that they store information that is costly to compute. Some of the terminology used when discussing predictors is the same as that for caches (one speaks of a hit in a branch predictor), but predictors are not generally thought of as part of the cache hierarchy.


The K8 keeps the instruction and data caches coherent in hardware, which means that a store into an instruction closely following the store instruction will change that following instruction. Other processors, like those in the Alpha and MIPS family, have relied on software to keep the instruction cache coherent. Stores are not guaranteed to show up in the instruction stream until a program calls an operating system facility to ensure coherency. The idea is to save hardware complexity on the assumption that self-modifying code is rare. Cache coherence refers to the integrity of data stored in local caches of a shared resource. ...


Implementation

Cache reads are the most common CPU operation that takes more than a single cycle. Program execution time tends to be very sensitive to the latency of a level-1 data cache hit. A great deal of design effort, and often power and silicon area are expended making the caches as fast as possible.


The simplest cache is a virtually indexed direct-mapped cache. The virtual address is calculated with an adder, the relevant portion of the address extracted and used to index an SRAM, which returns the loaded data. The data is byte aligned in a byte shifter, and from there is bypassed to the next operation. There is no need for any tag checking in the inner loop — in fact, the tags need not even be read. Later in the pipeline, but before the load instruction is retired, the tag for the loaded data must be read, and checked against the virtual address to make sure there was a cache hit. On a miss, the cache is updated with the requested cache line and the pipeline is restarted.


An associative cache is more complicated, because some form of tag must be read to determine which entry of the cache to select. An N-way set-associative level-1 cache usually reads all N possible tags and N data in parallel, and then chooses the data associated with the matching tag. Level-2 caches sometimes save power by reading the tags first, so that only one data element is read from the data SRAM.

Read path for a 2-way associative cache
Read path for a 2-way associative cache

The diagram to the right is intended to clarify the manner in which the various fields of the address are used. The address bits are labelled in little endian notation: bit 31 is most significant; bit 0 is least significant. The diagram shows the SRAMs, indexing, and multiplexing for a 4 KiB, 2-way set-associative, virtually indexed and virtually tagged cache with 64 B lines, a 32b read width and 32b virtual address. Image File history File links Read path for an associative cache Source is at . ... In computing, endianness is the ordering used to represent some kind of data as a sequence of smaller units. ...


Because the cache is 4 KiB and has 64 B lines, there are just 64 lines in the cache, and we read two at a time from a Tag SRAM which has 32 rows, each with a pair of 21 bit tags. Although any function of virtual address bits 31 through 6 could be used to index the tag and data SRAMs, it is simplest to use the least significant bits.


Similarly, because the cache is 4 KiB and has a 4 B read path, and reads two ways for each access, the Data SRAM is 512 rows by 8 bytes wide.


A more modern cache might be 16 KiB, 4-way set-associative, virtually indexed, virtually hinted, and physically tagged, with 32 B lines, 32b read width and 36b physical addresses. The read path recurrence for such a cache looks very similar to the path above. Instead of tags, vhints are read, and matched against a subset of the virtual address. Later on in the pipeline, the virtual address is translated into a physical address by the TLB, and the physical tag is read (just one, as the vhint supplies which way of the cache to read). Finally the physical address is compared to the physical tag to determine if a hit has occurred.


Some SPARC designs have improved the speed of their L1 caches by a few gate delays by collapsing the virtual address adder into the SRAM decoders. See Sum addressed decoder. The L1 data cache should usually be in the most critical recurrence on the CPU, because few things improve instructions per cycle (IPC) as directly as a larger data cache, a larger data cache takes longer to access, and pipelining the data cache makes IPC worse. ...


See also

Look up cache in Wiktionary, the free dictionary. ... Cache coherence refers to the integrity of data stored in local caches of a shared resource. ... This article is about the computer term. ... Memoization is a technique used to speed up computer programs by storing the results of functions for later reuse, rather than recomputing them. ... This is a list of the origins of computer-related terms (i. ... There are very few or no other articles that link to this one. ...

References

  1. ^ [1]

External links

  • Evaluating Associativity in CPU Caches — Hill and Smith — 1989 — Introduces capacity, conflict, and compulsory classification.
  • Cache Performance for SPEC CPU2000 Benchmarks — Hill and Cantin — 2003 — This reference paper has been updated several times. It has thorough and lucidly presented simulation results for a reasonably wide set of benchmarks and cache organizations.
  • Memory Hierarchy in Cache-Based Systems, by Ruud van der Pas, 2002, Sun Microsystems, is a nice introductory article to CPU memory caching.
  • A Cache Primer by Paul Genua, P.E., 2004, Freescale Semiconductor, another introductory article.

  Results from FactBites:
 
CPU cache - Wikipedia, the free encyclopedia (7028 words)
A CPU cache is a cache used by the central processing unit of a computer to reduce the average time to access memory.
For a cache read miss happening to instruction cache, the processor, or at least the thread of execution, has to wait (stall) until the instruction is fetched from main memory.
A victim cache is a cache used to hold blocks evicted from a CPU cache due to a conflict or capacity miss.
Cache - Wikipedia, the free encyclopedia (1853 words)
In computer science, a cache (pronounced /kæʃ/, like the English word cash) is a collection of data duplicating original values stored elsewhere or computed earlier, where the original data is expensive (usually in terms of access time) to fetch or compute relative to reading the cache.
Caches have proven extremely effective in many areas of computing because access patterns in typical computer applications have locality of reference.
The cache of disk sectors in main memory is usually managed by the operating system kernel or file system.
  More results at FactBites »

 
 

COMMENTARY     


Share your thoughts, questions and commentary here
Your name
Your comments

Want to know more?
Search encyclopedia, statistics and forums:

 


Press Releases |  Feeds | Contact
The Wikipedia article included on this page is licensed under the GFDL.
Images may be subject to relevant owners' copyright.
All other elements are (c) copyright NationMaster.com 2003-5. All Rights Reserved.
Usage implies agreement with terms, 1022, m